The CIF Single Sided Tinned Copper clad Pads for CEM 1 has 50x 100mm format.Drilled in steps of 2.54 mm Ø -> drilling 1 mm Interval between tracks 0.54 mm Track width 2 mm over the entire surface
The colour of the base laminate may vary between batches, from straw colour to dark brown - this does not affect electrical and mechanical performance. Matrix Boards. These SRBP panels are pierced ...
Cif Athelec Matrix BoardThe Cif Athelec matrix board is 50mm long and 100mm wide. It is a single-sided board with 1mm holes and 2.54mm pitch.Features and Benefits• 15/10th tinned copper clad pads o...
Prototype Board, standard, 2 mm grid, RE130. 35 μm CU on one side HAL hot dip tin-plated Hole pattern: 2 x 2 mm (0.79mil) Soldering islands 1.6 mm² 44 x 42 holes in rows Hole diameter: 0.8 mm Solde...
The colour of the base laminate may vary between batches, from straw colour to dark brown - this does not affect electrical and mechanical performance. Matrix Boards. These SRBP panels are pierced ...
Copper-tin plated square pad cards. Single-sided copper-tin plated square pad cards. 2.54 mm drilled pitch. Gap between tracks is 0.54 mm. Square pads 2 mm x 2 mm.
Top and bottom cover, battery cover, battery contact, 4 x screws and CR2032 sticker. Battery compartment for CR2032 x1. Takachi CS Slim Plastic Case. The Takachi CS Series is a slim handheld plasti...
Number of Sides = 1 Hole Pitch = 2.54 x 2.54mm Dimensions = 160 x 100mm Length = 160mm Width = 100mm Base Material = Synthetic Resin Bonded Paper Hole Diameter = 1.02mm FR Material Grade = FR2 Hole...
High Frequency Shielding Pads. These double-sided epoxy FR4 pads are fully plated with 2 mm2 tinned pads with a drilling diameter of 1 mm and connector DIN 41612. The other side is fully copper-cla...
Tinned Copper Test Card. This Test Card from CIF is drilled at a 2.54 mm pitch with a drilling diameter of 1 mm. 2 mm wide tracks cover the entire product surface which is produced from FR4 epoxy g...
Cif Athelec Matrix BoardThe Cif Athelec matrix board is 100mm long and 160mm wide. It is a single-sided board with 1mm holes and 2.54mm pitch.Features and Benefits• 15/10th tinned copper clad pads ...
Copper-tin plated square pad cards. Single-sided copper-tin plated square pad cards. 2.54 mm drilled pitch. Gap between tracks is 0.54 mm. Square pads 2 mm x 2 mm.
Cif Athelec Matrix BoardThe Cif Athelec matrix board is 100mm long and 220mm wide. It is a single-sided board with 1mm holes and 2.54mm pitch.Features and Benefits• 15/10th tinned copper clad pads ...
The CIF Tinned copper clad board has 1mm dia, pitch 2.5 mm 1 side and format 160 x 200mm.Drilled in steps of 2.54 mm Ø -> drilling 1 mm Square pads 2 mm side. Interval 0.54 mm over the entire surface.
Top and bottom cover, battery cover, battery contact, 4 x screws and CR2032 sticker. Battery compartment for CR2032 x1. Takachi CS Slim Plastic Case. The Takachi CS Series is a slim handheld plasti...
The CIF Tinned Copper Clad Strips,16/10mm has 160 x 200 mm format.Drilled at a pitch of 2.54 mm Ø -> drilling 1 mm Interval between tracks 0.54 mm Track width 2 mm over the entire surface Material:...
KM6 Veroboard® boards for DIN 41612 connectors. Single-sided boards combining the advantages of Veroboard, the flexibility of Eurocards and DIN 41612 connectors. For wiring by wrapping applications...
Euro Cards, HF board. This allows reliable HF, digital and analogue circuits to be set up. The component side is fully laminated, only the holes are etched. The second side is designed with solderi...
Copper-tin plated square pad cards. Single-sided copper-tin plated square pad cards. 2.54 mm drilled pitch. Gap between tracks is 0.54 mm. Square pads 2 mm x 2 mm.
Cif Athelec Matrix BoardThe Cif Athelec matrix board is 100mm long and 580mm wide. It is a single-sided board with 1mm holes and 2.54mm pitch.Features and Benefits• 15/10th tinned copper clad pads ...
Square Pad PCB. Recommended for wire-wrapping applications Epoxy glass - CEM 30 1.6mm thick, copper-clad Single sided Hole pitch 2.54mm (0.1in) Hole dia 1.0mm
Veroboard® Boards and Plug-in DIPs. A range of boards that is just as easy to use as the standard Veroboard, but which have a direct connector to provide a secure interface.
Eurocards: Lined on each side with through-hole. Quadratic soldering islands reduce risk of lifting during soldering. Simple connections to adjacent soldering islands can also be made. An earth scr...
Copper-tin plated square pad cards. Single-sided copper-tin plated square pad cards. 2.54 mm drilled pitch. Gap between tracks is 0.54 mm. Square pads 2 mm x 2 mm.
Square pad cards. Single-sided boards for wiring by wrapping, with optimum flexibility and maximum density. The DIP sockets are held in place by soldering the outer pins to the corresponding square...
Square Pad PCB. Recommended for wire-wrapping applications Epoxy glass - CEM 30 1.6mm thick, copper-clad Single sided Hole pitch 2.54mm (0.1in) Hole dia 1.0mm
Eurocards: Lined on each side with through-hole. Quadratic soldering islands reduce risk of lifting during soldering. Simple connections to adjacent soldering islands can also be made. An earth scr...
KM6 Veroboard® boards for DIN 41612 connectors. Single-sided boards combining the advantages of Veroboard, the flexibility of Eurocards and DIN 41612 connectors. For wiring by wrapping applications...
Square Pad PCB. Recommended for wire-wrapping applications Epoxy glass - CEM 30 1.6mm thick, copper-clad Single sided Hole pitch 2.54mm (0.1in) Hole dia 1.0mm
Double-Sided Microboards PTH. The component side of the card features a colander ground plane which assists glitch free high speed operation by dissipating switching spikes. This ground plane is so...
Square Pad PCB. Recommended for wire-wrapping applications Epoxy glass - CEM 30 1.6mm thick, copper-clad Single sided Hole pitch 2.54mm (0.1in) Hole dia 1.0mm
Boards with Square Pads and Foil Laminate Holes. The foil laminate allows wires to be placed in the same holes as the tails of the components, enabling very secure soldered connections to be made. ...
Boards with Square Pads and Foil Laminate Holes. The foil laminate allows wires to be placed in the same holes as the tails of the components, enabling very secure soldered connections to be made. ...