The Maxim DS9093S allows the user to permanently attach an iButton to an object with two screws, or rivets. The plastic plate is designed with an inset that accommodates the flange of the F5 packag...
Compact two-piece, all-metal receptacle for F5 MicroCan Accepts two-thirds of the MicroCan (one-third of MicroCan will extend out) Allows reading iButtons with either momentary or dwelled contact O...
Grove - Universal 4 Pin connector is the white 4-pin buckled connector used on Stem, Twigs and the Grove cables, the pin spacing is 2mm. There are 10 connectors per bag, Users can use them to DIY.
Grove - Universal 4 Pin connector 90° is the white 4-pin buckled connector used on Stem, Twigs and the Grove cables, the pin spacing is 2mm. There are 10 connectors per bag, Users can use them to DIY.
A general purpose LED module in Grove form factor, available in different colours. The ingenious PCB design enables you to bend the LED to any position you want, which makes it easy to use it stand...
The Parallax Inc through-hole, 80-way edge connector socket with 1.27 mm spacing holds the P2 edge module in a right-angle, parallel to the printed circuit board. This is a low insertion-force conn...
CONNEXT Cable would be a necessary tool used on M5Stack development, since all PORTs on M5Core are CONNEXT stadard. This CONNEXT cable, compatible with the CONNEXT port on M5Core,simply have 4 line...
Grove is a convenient plug-and-play system with specialized interface, but that doesnt mean it couldnt be used in open ecosystem like breadboard. With this special designed conversion cables, you c...
GROVE Cable would be a necessary tool used on M5Stack development, since all PORTs on M5Core are GROVE stadard. This Grove cable, compatible with the GROVE port on M5Core,simply have 4 lines, two f...
Compared with the Electronic Brick system, the Grove System uses only 1 type of cable, (the Electronic Brick system uses 4). These cables are compatible with all modules included in the Grove syste...
The Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Twigs to the Stem - Basic Shield or to other Grove compatible boards for quick prototyping. As a lot of users as...
The KKSB Okdo camera bracket kit for case, It is made of steel. This is compatible with different cameras such as Raspberry pi HQ camera and Raspberry Pi V2 and more. Also it is compatible with Okd...
Grove - Screw Terminal with four 3.5mm pitch pins rated up to 6A. Terminal can accept 30 to 20AWG wire. It is most commonly used pitch screw terminal. This Grove has four ports including GND, VCC a...
The Parallax Inc through-hole, 80-way edge connector socket with 1.27 mm spacing holds the P2 edge module in a vertical orientation on a printed circuit board. This is a low insertion-force connect...
When using HUSKYLENS, you may encounter accidental drops, bumps, etc. Now we carefully designed this silicone sleeve to protect your board. This silicone sleeve is small in size, cute in shape. It ...
The ICD2 Connector Board is used to connect the ICD2 / ICD3 programmer from Microchip with your development board or prototype device. The board solves your prototyping problems by offering a cost-...
The M5Stack LIGHT is a light intensity sensor unit with an adjustable photoresistor。 A photoresistor is a light-controlled variable resistor. The resistance of a photoresistor decreases with increa...
HUB is one of the six Units in M5GO, allowed buy separately. This Units is used for GROVE port expanding. Notice: HUB is just a pysical expander, if you are looking for software(standard protocol) ...
Seeed Studio Jumper WireThe Seeed studio jumper wire is a 4-pin female jumper to grove 4-pin conversation cable. It is made for using Grove modules directly with Arduino. This cable is compatible w...
The Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Twigs to the Stem - Basic Shield or to other Twig compatible boards for quick prototyping. As a lot of users ask...
Click board comes with the header strips soldered. Proto click mikroBUS™. We've a wide range of MikroElektronika click boards here at RS that add great functionality to your designs - however.. We ...
Click board comes with the header strips soldered. click BOOSTER Pack for LaunchPad. click BOOSTER Pack is an extension for the Texas Instruments Stellaris LM4F120 LaunchPad. It's an adapter which ...
PROTO is a pure universal prototype perboard. You can have the total freedom to make your own project as you want it, with prototyping perboards that allows laying out customized circult to interac...
mikroProg to ICD2 & ICD3 is an adapter board which allows you to connect mikroProg™ programmer and In-Circuit debugger to target board where only ICD2/3 connector is available for programming.
mikroProg to ST-Link v2 adapter allows you to connect mikroProg for STM32 programmer and hardware debugger to 20-pin male JTAG connector on your target board. Adapter is consisted of one 2x10 male ...
Flat cable with 16-pin female connectors, 20cm.This cable is used with the mikroBUS Shuttle.20 cm in length colour: grey Excellent quality 16-pin count Pitch: 1.27mm Current rating: 1A
Boe-Bot, ActivityBot and Shield Robot With Arduino Kits include 2 x Encoder Wheels and tyres as standard. Mobile robot encoder wheel ; tyre. A plastic wheel with an O-ring tyre designed to work wit...
The Parallax Inc adapter provides a convenient way to add wireless programming and serial communication capabilities to the Parallax Propeller P2 microcontroller. The adapter connects a Parallax ES...
The Parallax Inc P2 to MikroBUS click adapter connects MicroE Click series modules to our most popular Propeller 2 development systems for quick multicore prototyping and project design.Low-inserti...
The Parallax Inc USB to 2.1 mm ID centre positive power cord designed for use with the USB mains adapter. Together, these two parts provide a reliable 5V, high-current power supply. Use this pair w...
The M5Stack UHF-RFID is an ultra-high frequency (UHF) embedded wireless radio frequency reader module. The JRD-4035 module solution with built-in ceramic antenna completely eliminates the technical...
Pmod TPH2 12-pin Test Point Header. The Pmod TPH2 breakout module provides a 12-pin header for monitoring the signals passing between a host and a peripheral module. • 12 x breakout test-point pins...
The E1 Expansion Board is the perfect companion for the E1 Development board. The Board is a passive PCB with the outline of an Arduino UNO board. The board comes in a ready-state for installation ...
Click board comes with the header strips soldered. Adapter click mikroBUS™. The Adapter click board has been designed to help add-on boards with IDC10 headers, connect to development boards with a ...
2 x 6-pin gender changers, right-angle male header, 12-pin gender changer. Pmod Cable Kit, 12-pin. These extension cables let you locate a Pmod 150mm away from its host board, or use a 12-pin Pmod ...
The Digilent Pmod DIP is a 12-pin dual in-line package (DIP) that also includes a 2x6 female Pmod header, allowing users to easily separate and process any signals traveling to and from their 12-pi...
RGB LED always bring us vivid and magic light effect, especially when there are a large number of LEDs shining together. However it is not easy to connect all the LEDs together if you want to build...